Hagit Eden
6 years ago
“I had the pleasure working with Method Doors & Gates, great prices, very professional and friendly, arrived on time, Replace my garage door, excellent job highly recommend.”
Garage Door Opener Repair
Garage Door Opener Repair in Los Angeles
Humming, clicking, reversing, and a dead remote each point to a short list of causes. We diagnose yours before any part is replaced.
Diagnosis before a repair decision
Request a Repair Assessment
Tell us the location and symptoms. We'll call to discuss the visit.
No obligation. It takes about a minute, then we call to schedule. Prefer to talk? (818) 782-6180
Find your symptom
Start with how the opener behaves at the wall button. Each row names the parts we suspect first and links the section of our troubleshooting guide covering what you can safely check yourself.
| Symptom | Likely cause | Read more |
|---|---|---|
| Hums, but the door stays put | A stripped drive gear or sprocket, a lock left on, a broken spring, or a door stuck in a bent track | Won't open |
| Clicks, but the motor never starts | The logic board, the motor, or the wiring between them | Opener not working |
| Reverses before the floor, or won't close | Photo eyes blocked or out of line first, then the travel and force settings, then a door that binds | Won't close |
| Lights flash on the opener or a sensor | A fault signal; the safety sensors are the first thing to check | Won't close |
| Wall button works, remote or keypad doesn't | A remote battery, a lock or vacation setting, a lost keypad code, or the receiver | Won't open |
| Completely dead, with no lights | Power first: the wall outlet, its breaker or a tripped GFCI; then the board's power supply | Won't open |
| Strains, or stops partway up | A door that has become heavier: worn springs, lost balance, or a sticking roller | Won't open, and the balance check on a tune-up |
If you see a broken spring, a loose cable or a door hanging crooked, stop testing. Keep everyone out from under the door and call us.
Garage Door Opener Repair
Sensor, board, drive, or door: finding the opener fault
A garage door opener doesn't lift the weight of the door. The springs do that, and the opener moves a balanced door between its travel limits. It also watches for trouble. During every close, a modern opener checks that its safety sensors are present and working, and it reverses when the door meets more resistance than its force setting allows. That's why different faults look alike: a blocked sensor, a stripped gear, a failing logic board, and a door that binds in its track can all make an opener hum, click, stall, or reverse.
We start with the door. With the door down and the opener released, we check the balance by hand and look over the springs, cables, rollers, and track, because an opener fighting a heavy or binding door can fail again soon after a part is replaced. Then we test the opener in order: power and outlet, wall control, remotes and keypad, sensor alignment and wiring, travel and force settings, the logic board, and the drive gear, sprocket, chain, belt, or screw. You hear what failed and why before we recommend a repair.
Opener repair is priced after diagnosis, because the symptom alone doesn't show which part failed or whether that part is still made for your model. If the opener is old, parts are scarce, or the repair would cost close to a new unit, we tell you and quote the replacement as well. To start, call with the make and model if the label is visible from the floor, and tell us what happens when you press the wall button. Our phone is answered 24/7.
- Serving Los Angeles Since 2006
- Licensed, Bonded & Insured
- 24/7 Emergency Garage Door Service
- Written Price Before Any Repair
- Every Brand Serviced
Designs & details
Explore Garage Door Opener Repair
Project photographs alongside labeled design renderings and technical illustrations. Select an image for a closer look.
Repair assessment
Opener symptoms and what usually causes them
Hums but the door doesn't move
The motor runs and the door stays put. A stripped drive gear or worn sprocket inside the unit is a common cause, along with a locked door or a broken spring that leaves the door too heavy for the opener. A door stuck where its track is bent stalls it the same way, and that's an off-track repair.
Clicks but won't start
A click from the motor unit with no movement often means the logic board is calling for the motor and the motor isn't answering. Testing separates a failing board from a motor or wiring fault.
Reverses or won't close
Most often a blocked or misaligned safety sensor. If the sensors check out, the cause is usually a travel limit set wrong, a force setting that's too sensitive, or a door binding in its track, which the opener reads as an obstruction.
Lights blink
Many openers flash their lights, or an LED on the unit or the sensors, to signal a fault, and the safety sensors are a frequent cause. Some models flash a code that narrows the problem, so we read it before testing parts.
Remote or keypad dead, wall button works
If the wall button runs the door, the motor and board are working, so the fault is on the radio side: a dead remote battery, a lock or vacation setting on the wall control, a keypad that lost its code, or a failing receiver.
Nothing works at all
No lights and no response from any control points to power first: the outlet, the breaker, or a tripped GFCI. If power is reaching the unit, the logic board or its power supply is the next suspect.
Honest pricing
How we price garage door opener repair
What an opener repair costs depends on the part that failed and whether it's still available for your model. Resetting a travel limit, replacing a sensor, and replacing a logic board or drive gear are different jobs, and an opener straining against an unbalanced door may need the door repaired too. A phone quote can't account for any of that.
We diagnose on site and price the repair in writing before any work starts. When a new opener is the better value, we quote it alongside the repair.
Get Your Written EstimateWhat sets the number
- The failed part: sensor, board, gear, or motor
- Parts availability for your opener's model and age
- Remote and keypad compatibility
- Door repairs the opener needs to run reliably
- Wiring or outlet problems found on site
- Repair cost weighed against a new opener
The proposal separates the work being recommended so you can review the scope before approving it.
What to expect
How an opener repair visit works
Describe the symptom
Tell us what happens at the wall button and at the remote, whether the door is open or closed, and the opener's make and model if the label is visible.
Check the door first
We release the opener with the door down and check balance, springs, cables, rollers, and track, so a repaired opener isn't left fighting a door that binds.
Find the fault and price it
We test the sensors, wiring, controls, settings, logic board, and drive until the cause is clear, then give you a written price to approve.
Repair and retest
After the repair, we run the door through full cycles and check that it reverses on a rigid 2-inch obstacle, as California requires of anyone hired to service or repair an opener.
Reviews
What Customers Say About Working With Us
Nir Biton
6 years ago
“Method Doors&Gates Installed a new garage door in my house . Great price and service , door looks great. the job was done perfectly very professional.”
TRACY S
6 years ago
“Method Doors and Gates and Noam exceeded our expectations. Our gate and fence panels were installed last week. Installation was completed in four days with Noam directing and overseeing every aspect of the project. We are extremely pleased…”
Garage Door Opener Repair FAQ
Questions about garage door opener repair
Practical answers to help you plan the next step.
Start with power: make sure the opener is plugged in and the outlet, breaker, or GFCI hasn't tripped. Then try the wall button and a remote separately, look for anything blocking the sensor beam, check that the sensor indicator lights are on, and make sure the door's lock bar or the wall control's lock setting isn't engaged. If a spring looks broken or the door is damaged, keep people and cars out from under it and don't pull the emergency release.
No. Under the federal opener standard, 16 CFR Part 1211, which covers residential openers made since January 1, 1993, an opener must reverse when the door hits something and must also have a second safeguard, such as a photo eye, a sensing edge on the door, or a wall button you hold down to close. A bypass wouldn't work on a current opener anyway: the standard has it check its sensors on every close, and with one missing, faulty, or out of line, the remote can't bring the door down. If the sensors are the problem, we realign, repair, or replace them.
Usually because the door has gotten harder to lift, not because the opener has gotten weaker. Springs carry the door's weight, and when they wear or a roller binds, the opener works harder until it stalls or reverses. DASMA, the door and gate manufacturers' association, says openers are designed to open properly balanced doors and that a more powerful opener isn't the answer. If the springs are the cause, we quote that repair before any opener work.
Repair it if the opener is sound and the failed part is still made; replace it if parts are obsolete, failures keep coming back, or it lacks the safety features of a current opener. CPSC recommends replacing older openers that don't reverse with ones that meet the federal safety standard. A replacement opener installed at a California home must have battery backup under SB 969, and a replacement garage door can't be connected to an existing opener that lacks it. Compare drive types and features on our opener installation page.
Not always. Remotes have to match the opener's radio and security coding, and some newer openers accept only remotes made for their own system. We check compatibility before replacing a board or opener and tell you which of your remotes, keypads, and car buttons will still work with it.
Yes. We repair all the common opener brands and aren't affiliated with any manufacturer. Brand details such as learn-button colors, myQ, Intellicode remotes, and Aladdin Connect are on our LiftMaster and Chamberlain opener repair and Genie opener repair pages.
Service area
Garage Door Opener Repair across Los Angeles
From our office in Van Nuys we cover the San Fernando Valley, the Westside, and the neighborhoods in between.
- Bel Air, CA
- Beverly Hills, CA
- Brentwood, CA
- Burbank, CA
- Calabasas, CA
- Canoga Park, CA
- Chatsworth, CA
- Encino, CA
- Granada Hills, CA
- Hollywood, CA
- Lake Balboa, CA
- Los Angeles, CA
- Mission Hills, CA
- North Hills, CA
- North Hollywood, CA
- Northridge, CA
- Pacific Palisades, CA
- Pacoima, CA
- Panorama City, CA
- Porter Ranch, CA
- Reseda, CA
- San Fernando, CA
- Sherman Oaks, CA
- Studio City, CA
- Sun Valley, CA
- Sylmar, CA
- Tarzana, CA
- Universal City, CA
- Valley Village, CA
- Van Nuys, CA
- West Hills, CA
- West Hollywood, CA
- Woodland Hills, CA
Related services
Garage Door Opener InstallationBelt, chain, and wall-mount openers with battery backup and safety sensors, set up to work alongside your driveway gate's controls.- Garage Door Spring RepairTorsion and extension springs sized to the weight of your door and replaced as a set, with the cables, drums, and bearings checked on the same visit.
- Garage Door RepairBroken springs, snapped cables, doors off track, and openers that hum but won't lift, diagnosed on site with a written price before any work starts.
Guides & answers
Garage Door Opener Buying Guide: Belt, Chain or Wall-Mount, Battery Backup (SB 969), Horsepower and Smart FeaturesBelt or chain, rail or wall-mount, what horsepower and DC ratings mean, California’s battery-backup rule, the safety tests every opener must pass, and when one remote can run gate and door.- Garage Door Troubleshooting: Won’t Open, Won’t Close, Opener Not Working, Noisy — Safe Checks Before You CallPhoto eyes, power, the lock button and a look at the hardware from the floor are the checks you can make; springs, cables and drums are the parts you never touch.
Brands we repair
- Clopay Garage Door Repair
- Wayne Dalton Garage Door Repair
- Amarr Garage Door Repair
- LiftMaster & Chamberlain Opener Repair
- Genie Garage Door Opener Repair
We service these brands independently and are not an authorized dealer for any of them.
Written price before any repair · Answered 24/7
Let’s Discuss Your Repair
Call with the address and what the door is doing. We answer 24/7 and will discuss service availability and next steps for your property.
No obligation
Request a Repair Assessment
Tell us the location and symptoms. We'll call to discuss the visit.
No obligation. It takes about a minute, then we call to schedule. Prefer to talk? (818) 782-6180